How to Put a Permanent Crease in Pants

Putting a permanent crease is not a big deal. But it needs a proper guideline. Luckily, you are on the right page now. This post contains the easiest path to do so!

Before we get into the core topic, it would help if we clarified two notions for you. Let us know about the crease in pants and the permanent crease in pants.

What Is Crease in Pants?

It runs down the front of most slacks vertically. Such a crease ensures sharpness to the look of a person. In other name, this fold is called a traveler’s crease. Often we hang our pants in a garment bag. In that case, it helps keep the pants neat!

What is a permanent crease in pants?

A permanent crease provides your pants with an ironed look. It does not only bring sharpness but makes your leg taller and slimmer. You will place a perfectly safe and specially formulated resin inside the crease in this process. As a result, you will get a stunning effect on your pants.

How to Put a Permanent Crease in Pants – Steps Showing

You might not be someone from the Southern part. Nonetheless, your pants can be creased and starched as if you are a cowboy!

Let’s say you have a pair of jeans. Now we are going to state the steps to help you put a permanent crease in your pants. All you need to do is- make a crease and repeat the task for a permanently creased look. Anyway, the steps are as follows!

Step One

The first job is to wash the jeans. You will need to employ a high heat setting in your washing machine. Then put them into the dryer. Again, ensure a high heat. By this, your jeans will shrink to some extent, and it will be helpful for the creasing project.

Step Two

Before completing the cycle, pull the jeans out of the dryer. Why? Because this slightly damp garment will leverage you to put a crease into the jeans.

Step Three

Now, it’s time to create the crease, so fold the jeans. It should reach the legs’ center. For this, you need to match the sides and cuffs of your jeans. It will help gain the exact creases. The crease should aim to break down the middle of each knee.

Step Four

Get an ironing board to flatten your pants and employ high heat. Now keep ironing over the creases. Set the crease using a heavy hand.

Step Five

The following job is to starch the jeans. The creases require a heavy amount of starch. Then employ the hot iron over the creases. Press down the iron several times to create a permanent crease.

Step Six

Two things can ensure the sharpness of your pants- wash, and iron. Ensure both. Else, you may prefer starching optionally.

Apart from the stages above, you may have a look at the clip below. It will let you know how to set a permanent pant crease practically.

The Alternative Way to Make Permanent Fabric Creases

Do you want to try a different method to create a permanent crease? Then you have to follow a few steps. These are as follows!

Have a two-thirds cup of water and one-third cup of vinegar.
Next, mix them up.
Now dampen the fabric’s targeted area where you need a permanent crease using a spray bottle.
Afterward, cover the portions with some brown paper.
Finally, iron your pants.

Do Your Chinos Need Creases?

Pressing flat chinos by ironing is better than having a crease down the front. On the other hand, a crease should be there in a pair of grey flannels or suit trousers. This sharp look will help take your leg off at the knee. Remember, you need to press flannels or suit trousers after dry cleaning.

Else, the ironing depends on the type of your fabric. Please have a look at the clip below!

The Reason for Having a Crease in Dress Pants

Hopefully, you don’t want to do something without reason. The core purpose of having a crease is to get a sharp and sophisticated look. A long vertical crease is attention-grabbing and flattering.

How to Iron Trousers Step by Step

The tutorial given below will help do the operation efficiently. Don’t miss it either!

How to Starch Jeans

Starching is a vital part of creasing. Therefore it would help if you secured a sound knowledge of this. Jeans pants are one of the most favorable stuff due to their casual and comfortable feeling.

A number of users are fond of starched jeans for a wrinkle-free and fitted look. For example, starched blue jeans are lovable to many as they maintain creases and provide a professional look. Many people embrace this!

Instead of denim, dirt and grime stick to the starch. So you will find it clean for a long. That means you can wear the pants several times before a wash.

Apart from going to a professional cleaner, you can starch by yourself. It will help save laundry expenses. So here in this part, we will be showing how you can starch your jeans pants in different ways. Cool enough?

Okay, let’s see the methods below!

How to Starch Jeans in the Washing Machine

One of the most reliable ways to starch jeans can be a regular wash cycle in your washing machine. You might have several pairs of jeans to starch, right? Then it would be best to wash and starch them at the same time.

Please follow the steps below one by one.

First of all, put your jeans in the washing machine.
Ensure either cold or warm water cycle.
Apply a laundry detergent.
Then add liquid starch during the rinse cycle.
After completing the washing cycle, hang the jeans to dry. Alternatively, you may dry them in your dryer.
Iron them if you want additional crease in your jeans.

Use Cornstarch to Starch Jeans

You can easily find cornstarch in your kitchen pantry and use it to stiffen your jeans pants. If you are looking for an affordable, easy option, then this one is apt for you. To be more specific, you don’t need to buy a store-bought liquid starch spray. Instead, you can easily prepare a liquid starch, spray it on your pants, and create a creased look.

Here is the procedure through which you can prepare and apply this.

Get a bowl to combine one tablespoon of cornstarch with two cups of cold water.
Unless the cornstarch is fully dissolved, keep agitating.
Have a spray bottle and pour the starch mixture into it.

That’s it. However, it would help if you shook the bottle vigorously before each use.

How to Starch Jeans by Ironing

Here we go for the third method. This approach requires an ironing board and a liquid starch spray. As soon as you finish ironing, you may put on your pants!

Please have a look at the steps below!

Wash your pants. You may either choose hand wash or machine wash.
Then dry the jeans.
Now lay your jeans flat on an ironing board.
Next, before you spray the starch liquid, shake it properly.
Then start spraying from small areas like the waistband, zipper, etc.
Dampen the jeans slightly.
Allow the spray to sit for one or two minutes.
Then go ironing. Start from the legs and gradually cover the whole body.

How to Supercrease Pants

Dress pants and slacks users expect an air of professionalism to their look. That’s the reason they want sharp, crisp creases in pant legs. Creases in pants are common after a wash among those who constantly work.

You will be free from ironing every time if you ensure a sharp, permanent crease in your pants. Then how can we do so? Well, there are two easiest means to create long-lasting creases in your pants- adding fusible thread to the crease and ironing the crease with a vinegar mixture.

The Vinegar Mixture Method

It includes some steps. These are as follows!

Have some water to fill your iron.
Then turn the steam on and set the heat level according to the fabric type.
Your pants need to be half-folded. For this, lay one pant leg over the other on the ironing board. Make sure that the seams match.
Get a spray bottle and combine water and vinegar equally.
Dampen a cloth with that spray.
Now by starting from the pocket area, press the folded front edge of your pants with that damp cloth.
Move your iron in a circular motion and press it over the top of the damp cloth until the cloth is dry.
Next, re-dampen the cloth.
Then press it to the next part. Keep it up.
Spray the cloth piece and press that over the crease line.
Next, repeat the process on the other side of your pants by turning it over.
At last, let your pants dry and cool down. It will help set the crease properly.

The Fusible Thread Method

Let one of the legs lay on top of the other by turning the pants inside out.
Then create a crease by ironing the front edge of the pants.
Your fusible thread should have enough length to fit the crease length. So cut it accordingly.
Then lay it at the very edge of the pressed crease line.
Afterward, iron over that to melt the fusible thread into the crease.

How to Put a Permanent Crease in Uniform Trousers Using Glue

Having crisp, wrinkle-free uniforms is a matter of pride among the American military staff. Keeping uniforms in tip-top shape is almost impossible for them. They remain in harsh physical conditions or uncooperative weather generally.

In spite of that, keeping the center crease in uniform pants pristine is vital to the service persons. Therefore, they tend to create a permanent fold in their trousers.

Now, we are going to show you the way. See how you can place a crease in uniform trousers by using glue. Please follow the steps below!

Have some water and fill your iron.
Let the iron heat.
Get some heavy starch to spray the trousers.
Then iron the creases.
Now apply PVA adhesive or polyvinyl acetate glue upon the front and rear creases. Cover both the trouser legs.
Get a bowl to insert into your trousers. It will help hold the leg open and see things obviously.
Then precisely fold the trousers and hang.
Let the glue set and dry. Wait at least 24 hours for this.

How to Get Permanent Creases in Wranglers

Things become dull unless your jeans have the perfect frontal crease! If you want to gain a real cowboy style, you cannot compromise, can you? Likewise, you can come up with a perfect western look when you know the steps to put a permanent crease in a pair of Wranglers!

No worries, you merely need a few basic materials. It takes less than an hour only. Now allow us to mention the steps below!

Before all, wash your jeans in the washing machine by employing a hot setting.
Then dry it in a similar setting.
However, bring out the jeans when it is still damp to some extent.
Then match the inner leg seams by grasping the ankle cuffs of the jeans and holding them in the air.
Afterward, lay the legs flat against each other. The aim should be to keep the inner-leg seams together.
Then lay it on the ironing board to smooth out any wrinkles from the damp, hot jeans. Use your hands.
Next, iron your jeans for five minutes.
Then shake your laundry starch can.
Now spray a fine mist over the entire exposed surface of your jeans by holding the nozzle about 4 inches from its surface.
Then start pressing the iron from the cuffs to the upper thigh or hip area.
Let the iron rest across the layered width.
Turn the jeans over. Shake and iron the jeans again.
Finally, spend 30 minutes cooling the jeans.

How to Add a Permanent Stitched Crease

You may need to deal with a Simon Set. In that case, learning to sew a permanent crease down the front legs would be helpful. Just before you learn the process, let us be clear about the stitched crease.

What Is a Stitched Crease?

You might have seen it on tracksuit bottoms or tailored trousers. Some people love to add the stitched crease to Simone. Despite being casual and relaxed, such a crease can provide thoughtful design detail.

It is also known as pintuck. Have you noticed the Farah slacks of the 70s? Dear, it will remind you of a permanent stitched crease.

Usually, the position of a stitched crease is on the front trouser leg. However, you may feel free to add it to the back leg as well. Then what if there is a dart in your stylish trouser? Well, you can cap your crease at the dart’s base. And the crotch level will be the apt place for the back crease.

Remember, it might seem to be a straightforward hack but desperately needs to be accurate. Before you start constructing your trouser, you have to stitch the crease.

Adding a Permanent Stitched Crease

It would help if you get a scrap of fabric for a test. Even if you are not a beginner, you should have a test. Why? Because a fabric may behave unprecedently. So it can be a safe attempt for you, and you can do it more confidently.

Now please follow the steps below! These would all be about pressing.

First of all, fold the front trouser leg in half with the wrong side of the fabric together.
Then line up the lower legs and hem carefully.
Next, place the trouser leg on grain.
Afterward, aim at the fold’s entire length and press a crease along it.
If your fabric supports, do not hesitate to apply steam. Do it in an up and down motion. Otherwise, dragging the iron will be devastating as it distorts the shape.

Now let us move toward the sewing part. Naturally, it also includes some phases. Please have a look at the points below!

Make sure that you have a longer topstitch length. It will help secure neater and straighter-looking stitches. So it would be best to set the stitch length slightly longer than usual. It can be approximately 3mm.
Ensure you have a matching colored thread.
Let the trouser leg folded with the right side of the fabric up. And the sewing needle needs to be 1.5-2mm (1/16″) from the folded edge.
Now it is time to edge-stitch. Cover the entire crease. You can either use an edgestitch foot or a regular presser foot.
Sew in a slower motion. You need to make your stitching is as straight as possible.
Then without laying to either side, gently press the crease as well as the pintuck stands up.
Keep sewing your Simone trousers as soon as both legs achieve their stitched crease.

A Small Pintuck Versus A Bing Tuck

Sewing a tiny pintuck matters a lot. No doubt that it looks nice. However, the aim of sewing a permanent crease in the front is to minimize the width of the trouser. Thus, your fabric will be a bit smaller. As a result, you will get it slightly tighter on the hips.

The reduction would be around 6-8mm in total. Therefore, it will not be visible. A bigger pintuck means more reduction in width. The picture above displays the difference.

See, the leg on top has been stitched by employing the machine foot (stitched 7mm from the edge) while the trouser leg at the bottom has been stitched with a tiny pintuck. It differs in width significantly. It is going to be doubled over two legs that measure 2.8 cm to be more exact.

Frequently Asked Questions

Question: What is a crease line?

Answer: A crease line is a mark, ridge, or line that you create by a pliable substance. Simply put, it is a line surrounding a crease.

Question: What is a double crease in pants?

Answer: Often the dry cleaners come up with a double crease down the front, and it remains unsightly. When a dry cleaner arranges pants improperly, faces this issue. Let your pants get folded on the front and back crease. The stretched-out leg will help smooth out wrinkles. Thus, you can resolve this.

Question: What is a pressed crease?

Answer: Usually, a pressed crease meets waistline darts, tucks, or pleats in the front by starting at crotch level in the back.

Question: What is the difference between slacks and dress pants?

Answer: Dress pants features a dressier look. You will find them in different styles. However, they are not as loosely fitting and comfortable as slacks. If you want a formal appearance, you should opt for dress pants. On the other hand, slacks will provide a more casual appearance.

Question: Should you crease flat front pants?

Answer: You may prefer pants with flat fronts for a casual occasion. Then it is okay to get your pants pressed flat void of a center crease in the legs.

Question: How do you remove an ironed crease?

Answer: Well, you need to manage white vinegar and water to mix them up. Then get it into a spray bottle to apply to the stubborn crease. Get your iron to steam and press the fabric. That’s it!

Question: How do you get train tracks out of pants?

Answer: Have some water in a spray bottle to squirt over the pants. You will do it as a pre-task of ironing. Indeed, it is an easy yet excellent means to train tracks or crease marks.

Question: How do you get rid of crease lines?

Answer: Get a soap bar to dab your pants’ inner side along the crease line. Then turn the pants right-side-out. Place them on the ironing board to iron. Afterward, have a clean cloth to dampen with white vinegar. Then rub it over the crease of your pants. Finally, iron them again.

Question: Are creases in pants out of style in 2020?

Answer: Creases elongate your legs by creating vertical lines. However, though they look nice on dress pants, you should not expect them on jeans, denim, etc. The latter ones are too casual for creases.

Question: What does ironing mean?

Answer: It is the process or acts to press or smooth a piece of garment with a heated iron.

Question: Is pressing the same as ironing?

Answer: Often people confuse these terms but they possess different meanings. The act of pressing means the placing of the iron upon your fabric by holding and removing. On the other hand, ironing is all about sliding the iron back and forth on a fabric.

Question: Do cargo pants need to be ironed?

Answer: No, you should not iron cargo pants or jeans. However, if you want the western look, you may do it.

Question: Why are cowboy and cowgirls jeans so crispy?

Answer: Simply because the cowboys and cowgirls are fond of crispy patterns on their jeans. To treat these pants, you need to let the starch impregnate the fiber. It makes a seal by sliding off all the specks of dirt. You can rub the dirt after drying.

Question: Should I crease my khakis?

Answer: A bit of wrinkling is natural in khakis. You should not iron a crease into your khakis. If you want a more professional look at it, use a crisper.

Question: What causes permanent wrinkles in clothes?

Answer: Heat and water are the main causes of permanent wrinkles. Hydrogen bonds hold water molecules and polymers together. These get broken in fabrics by heat. Consequently, you get wrinkles in your clothes.

Question: Can you sew creases into clothing?

Answer: The number of creases may be too much. You may also want to sew them. Permanent creases make you press them frequently for the sake of their sharpness and crispness. However, there is no need for pressing if you sew a permanent crease in your cloth. Thus, you can become free from its maintenance.